Pose ton son Play

Guide

How to wire a sound system

Every sound system follows the same chain: sources, mixer, processor, amps, speakers. The rest comes down to a few rules: never go below the amp’s minimum load, never clip, use thick enough cable and size your power properly. Here is how it all works, with real numbers.

Updated 16 November 2026 9 min read

The signal chain, from record to speaker

A sound system is a chain. The signal leaves the sources, goes through the mixer, then into the processor that splits it into bands, before being amplified and sent to the speakers. Every link has a job, and the weakest one sets the quality of everything after it.

Signal chain of a four-way sound systemSourcesdecks, laptop, live gearXLR or jackMixergain, EQ, masterXLRProcessorcrossover, delay, limitersAmpspeakONSub35 to 90 HzAmpspeakONKick90 to 250 HzAmpspeakONMid250 Hz to 2 kHzAmpspeakONTop2 to 20 kHz
The signal flows from the sources down to the speakers. The processor splits the bands: one amp channel per band. Crossover points are typical values.
  • Sources: turntables, CD or USB players, a laptop, synths and drum machines for live sets. They put out a weak line level signal (phono level for vinyl decks, which go into the mixer’s phono inputs).
  • Mixer: blends the sources and sets their levels. Its master output runs on XLR to the processor.
  • Processor, or crossover: the brain of the rig. It splits the signal into frequency bands, sets delay and polarity for each band, handles EQ and protects the drivers with limiters.
  • Amps: they turn the small line signal into enough power to move the cones. One amp channel per band and per group of speakers.
  • Speakers: the boxes themselves, passive here. Active speakers have the amp, and often the processing, built in and take an XLR feed directly.

Sub, kick, mid and top: the bands of a rig

No single driver can reproduce everything. A free party rig therefore splits the spectrum into three or four bands, each handled by dedicated boxes:

  • Sub (around 35 to 90 Hz): the bass you feel in your stomach. 18 inch drivers in horn-loaded or bass reflex cabinets.
  • Kick (around 90 to 250 Hz): the punch of the kick drum that hits you in the chest. Usually 15 inch drivers.
  • Mid (around 250 Hz to 2 kHz): vocals, synths, the body of the music. 10 or 12 inch drivers, often horn-loaded.
  • Top (above roughly 2 kHz): hi-hats, air and detail. Compression drivers on horns.

These crossover points are not set in stone: they depend on your boxes, and the manufacturer’s spec sheet has the final word. Two settings matter more than anything. Never send low frequencies into a tweeter: it will die in seconds. And always put a high-pass filter on the sub band, just below its lowest usable frequency, so the cones don’t flap wildly on infrasound nobody can hear.

Speaker impedance: series, parallel and minimum load

Impedance, measured in ohms (Ω), is how much a speaker resists the current coming from the amp. The lower it is, the more current the amp has to deliver. Every amp has a minimum load per channel, usually 4 Ω or 2 Ω: go below it and the amp overheats, goes into protect mode or eventually dies.

When you connect several speakers to one amp channel, their impedances combine:

  • In parallel, the usual way, daisy-chained through the speakers’ link sockets: impedance goes down. Two 8 Ω speakers make 4 Ω, four make 2 Ω. For identical speakers, divide one speaker’s impedance by how many there are.
  • In series: impedances add up. Two 8 Ω speakers make 16 Ω. The amp has an easy time, but it delivers far less power.
Two 8 ohm speakers wired in parallel, then in seriesParallelAmpmin load 4 Ω+−8 Ω8 Ω= 4 ΩSeriesAmpmin load 4 Ω+−8 Ω8 Ω= 16 Ω
In parallel, impedance drops: two 8 Ω speakers give 4 Ω. In series it adds up: 16 Ω. Always check your amp’s minimum load.

Two classic traps. In bridge mode, each side of the amp sees half the load: an amp that is stable at 2 Ω per channel should not go below 4 Ω bridged. And the impedance on the label is nominal: the real curve dips below it at some frequencies. An amp already running at its minimum load has no safety margin left.

Amp power vs speaker power

On a spec sheet, the figure that counts is continuous power, labelled AES or RMS. “Program” and “peak” ratings are two to four times higher and are mostly there to sell.

The common rule: pick an amp that delivers 1.5 to 2 times the speaker’s AES rating at the same impedance. It sounds like a lot, but that reserve, the headroom, is what keeps the amp from clipping on peaks. How much power actually reaches the speaker is capped by the processor’s limiters.

It sounds backwards, but an underpowered amp is more dangerous than an overpowered one. Amp clipping chops the top off the waveform and turns it into something close to a square wave, packed with high harmonics and average power. That is how people blow tweeters with a “small” amp.

Three rules of thumb for loudness:

  • doubling the power only gives you +3 dB; you need ten times the power for +10 dB, which the ear hears as twice as loud;
  • sensitivity (dB at 1 W, 1 m) tells you how much level a speaker gets out of each watt: 3 dB more sensitivity is worth an amp twice as powerful;
  • outdoors you lose about 6 dB every time the distance doubles.

Gain structure: keep the mixer out of the red

Gain structure means setting every stage so the signal is strong enough without ever clipping. One golden rule: no red on the mixer. A clipping mixer sends out a signal that is already distorted, and nothing further down the chain can fix it.

  1. Power up in order: mixer, processor, then amps last. Power down the other way round, amps first. That avoids the thump that damages drivers.
  2. On each mixer channel, set the input gain (trim) so peaks just touch 0 dB on the meter.
  3. Keep the master around 0 dB and check the processor input isn’t clipping.
  4. Bring the amps up to their usual setting (often fully open, or what the manufacturer recommends), with the processor’s limiters matched to your speakers’ power handling.
  5. Want it louder? Add boxes, not gain.

Cables: XLR, speakON and wire gauge

Two families of cable that must never be mixed up:

  • Signal, at line level: balanced XLR from the mixer to the processor and from the processor to the amps. A balanced line rejects interference and happily runs for tens of metres. Avoid unbalanced jack or RCA over long runs: they hum and pick up everything.
  • Power, at speaker level: speakON, the locking connector designed for it. Never run an amp output through an XLR cable, even if the plug fits: the cable is too thin, and sooner or later someone will plug a mixer into it.

For speaker cable, the cross-section has to follow the length. Cable that is too thin and too long acts like a resistor: it heats up, eats power and softens the bass. A safe rule is to keep the cable’s round-trip resistance under 5 % of the load, which means losing less than half a decibel. For copper, that gives:

Cross-sectionMax length into 8 ΩInto 4 Ω
1.5 mm² (about 15 AWG)17 m8 m
2.5 mm² (about 13 AWG)29 m14 m
4 mm² (about 11 AWG)46 m23 m
6 mm² (about 9 AWG)69 m34 m

Into 2 Ω, halve those lengths again. Beyond that, move the amps closer to the speakers and run XLR instead, which loses nothing over distance.

Power: generator, circuits and earth

A free party rig runs on a generator, and it is often the first thing to give up. To size it:

  1. Add up the amps’ power draw, not their output power: manufacturers list current draw with music, often measured at 1/8 or 1/3 of rated power. Add the mixer, processor and lights.
  2. Pick a generator that covers that total at no more than about 75 % of its continuous rating, all night long.
  3. Watch out for kVA: multiply by about 0.8 to get kW. For a 6 kW draw you need 8 kW continuous, so a generator of around 10 kVA.

For distribution, in France a 230 V circuit on a 16 A breaker gives at most 230 × 16 = 3,680 W. In practice keep a margin and spread the amps over several circuits instead of loading one. On a three-phase generator, balance the phases.

  • Fully unroll extension reels. A coiled cable heats up: the power it can take coiled is far lower than unrolled. Read the label.
  • Connect the earth. The generator goes to an earth rod, with a 30 mA RCD at the head of the distribution. Never lift the earth on a device to kill a hum: that is how people get electrocuted.
  • Keep the generator away from the dancefloor, exhaust downwind: carbon monoxide gives no warning. Store fuel separately.

Placement, delay and subwoofer phase

Placement

Put the subs on the ground and keep them together: packed side by side they reinforce each other, and the ground adds even more low end. Tops go above head height, aimed at the crowd, so they throw far without tearing the front row’s ears off. On a wall the heavy boxes always stay at the bottom, and every stack must be stable, straps included.

Delay for distant stacks

Sound travels at about 343 m/s, roughly 3 ms per metre. If you set up a second stack 20 m behind the main wall to cover the back of the floor, delay it by about 58 ms in the processor. Otherwise people at the back hear every kick twice. The same idea aligns the bands within one stack when the sub and the top don’t sit at the same depth.

Polarity and phase

Every driver has to push the same way at the same moment. If a cable or a box is wired backwards, two subs side by side partly cancel out and the bass vanishes right in front of the wall. To check, use a polarity tester, or your ears: one sub alone, then both, and the bass should clearly grow. If it sounds thinner, flip the polarity of one of them in the processor, then fix the faulty cable. Every trap of this kind is covered in the most common sound system mistakes.

FAQ

How do I connect two speakers to one amp?

Either one speaker per channel, or both on the same channel in parallel through the link socket: two 8 Ω speakers then give 4 Ω, and the amp must handle 4 Ω. In series they make 16 Ω: perfectly safe, but much less power.

What size generator for a sound system?

Add up the amps’ power draw with music, plus mixer, processor and lights, then choose a generator that runs that total at 75 % of its continuous rating at most. For a 6 kW draw, plan on about 10 kVA.

Why does my amp keep going into protect mode?

Most of the time the load is too low: too many speakers in parallel on one channel. Next come overheating, a shorted cable and clipping. Check the impedance first. The other causes are in the sound system mistakes guide.

Build your rig, play your sound

Pick your spot on the real map, buy your gear, load the truck and get ready for the biggest free party. Free, in your browser, nothing to install.

Play for free