Pose ton son Play

Guide

The 14 most common sound system mistakes

Most sound system failures come down to the same few mistakes: a mixer in the red, too many speakers on one amp, an underpowered amp pushed flat out. Here are all fourteen, from the most common to the rarest, each with the fix.

Updated 16 November 2026 6 min read

Mistakes you see at every party

Running the mixer in the red

The DJ turns up the gain, then the master, and every meter is flashing red. The signal clips before it even reaches the processor: the sound turns harsh and the limiters never stop working. Louder on the mixer doesn’t mean louder from the speakers, just dirtier.

The fix

Set input gains so peaks touch 0 dB, keep the master around 0 and put a limiter in the processor. If it still isn’t loud enough, you need more boxes, not more gain. The full method is in our guide to wiring a sound system.

No earplugs

In front of a wall, levels often go past 105 dB for hours on end. The next day your ears ring; over time the damage becomes permanent. That goes for the crowd, and even more for the crew who spend whole weekends next to the boxes.

The fix

Foam earplugs in every pocket, moulded plugs for the crew, regular breaks away from the rig, and a box of earplugs out for the crowd.

Speaker impedance too low

Three 8 Ω speakers daisy-chained on one channel make 2.7 Ω, four make 2 Ω. An amp rated for 4 Ω overheats, goes into protect and cuts out mid-party, if it doesn’t blow first.

The fix

Work out the load on each channel before chaining (one speaker’s impedance divided by the number of identical speakers in parallel) and stay above the amp’s minimum load. Give the amps room to breathe.

Amp clipping: an underpowered amp pushed flat out

An amp with half the power of the speakers, turned all the way up, clips: the tops of the waves get chopped off and the signal turns almost square. That shape pumps a lot of energy into the highs and heats up the voice coils. Tweeters and compression drivers go first. A clip LED that stays lit is your alarm.

The fix

An amp rated at 1.5 to 2 times the speakers’ AES power, properly set limiters in the processor, and an eye on the clip and limit LEDs all night.

Very common, and expensive

An undersized generator or an overloaded circuit

The whole rig is plugged into one extension lead and the breaker trips on the first big kick. Or the generator is too small: the voltage sags on every bass hit and the amps drop out one after another.

The fix

Add up the amps’ power draw, pick a generator that runs that total at no more than 75 % of its continuous rating, and spread the amps over several 16 A circuits. Fill the tank before the party and keep a spare can.

Ground loop hum

A low, steady buzz comes out of the whole rig, even with no music playing. The usual suspects: a laptop on its charger, a long unbalanced cable, or gear plugged into distant sockets whose earths sit at different potentials.

The fix

Power all the audio gear from the same distribution, use balanced XLR lines, and put a DI box or line isolator between the laptop and the mixer. Never lift the earth to kill the noise: it is what keeps you from being electrocuted.

Speaker cable that is too thin and too long

Thirty metres of 1.5 mm² cable into 4 Ω adds almost 0.7 Ω of resistance: more than a decibel lost, flabby bass and a warm cable.

The fix

Match the cross-section to the length (the table is in the wiring guide), keep amps close to the speakers, and cover long distances with XLR, which loses nothing.

The ones nobody notices

Subwoofers out of phase

A speakON cable rewired backwards, a box rebuilt with crossed wires: the two subs push in opposite directions and partly cancel out. Each one sounds fine on its own, but together the bass disappears right in front of the wall.

The fix

A polarity tester at every setup, or the ear test (one sub, then two: the bass should clearly grow), and labelled cables so they never get mixed up again.

Swapped bands, or no crossover at all

The processor’s sub output goes into the tops amp and the compression drivers die within seconds. The other version: speakers run full range without a processor. The subs wear themselves out on highs they can’t play, and the tops take bass that destroys them.

The fix

One colour per band on processor outputs, amps and cables; test each band on its own at low volume before turning up; and always a processor or crossover between the mixer and the amps.

Distant stacks with no delay

A stack at the back of the floor plays at the same time as the main wall. In the middle, every kick arrives twice, a few dozen milliseconds apart, and the sound turns to mush.

The fix

Delay the distant stack by about 3 ms per metre in the processor (20 m is about 58 ms), then check by ear halfway between the two.

Rarer, but they end badly

Unstable stacks

A heavy box on top of a light one, a stack too tall on soft or sloping ground, and the vibrations walk the boxes forward during the night. An 80 kg speaker falling on someone can kill.

The fix

Heaviest at the bottom, flat and firm ground (boards or pallets if needed), ratchet straps, a sensible height, and nobody climbs the stacks.

Rain and power

The generator out in the rain, extension leads in puddles, amps uncovered: short circuits, tripping breakers and a real risk of electrocution for everyone.

The fix

Tarps and gazebos packed in advance, connections raised and covered, a 30 mA RCD, and if the water wins, shut everything down.

Pointing the wall at the neighbours

Bass carries for miles, especially at night. A wall aimed at the village means guaranteed complaints and a party that may not last long.

The fix

Spot the houses before you set up, turn the wall away from them and use the terrain, since a hill behind you blocks part of the sound. Bear in mind that bass spreads in every direction: aiming mostly helps with mids and highs, and only distance really takes care of the rest.

No spares

A speakON cable that fails at 3 am, a blown fuse, a cracked tweeter diaphragm: without spares, a whole band goes silent until morning.

The fix

An emergency box with extra XLR and speakON cables, fuses, replacement diaphragms, a power strip, a head torch, gaffer tape, a multimeter and basic tools.

The checklist before you turn it up

  • The load on every amp channel is above its minimum load.
  • Every band has been tested alone, at low volume, on the right boxes.
  • Sub polarity has been checked.
  • Processor limiters are set and distant stacks are delayed.
  • Reels are unrolled, the earth is connected, circuits are balanced.
  • The generator is full and a spare can sits well away from it.
  • Stacks are stable and strapped.
  • Earplugs are in pockets and the emergency box is in the truck.

Practise without frying anything

Pose ton son is a free multiplayer free party game that runs in your browser. You build your sound from scratch: your home on the map, your gear, your truck, your wall and your crew.

To go further, read how to wire a sound system and the story of the free party.

FAQ

Why does my amp keep going into protect mode?

From most to least common: a load that is too low (too many speakers in parallel on one channel), overheating from poor airflow, a shorted cable, or a clipping signal. Check each channel’s impedance first.

Why do my tweeters keep blowing?

Usually an underpowered amp that clips, or bass reaching the tops because the crossover is missing or the bands are swapped. A well-set limiter in the processor and an amp with enough power solve most of it.

How do I get rid of hum in a PA?

Power all the audio from the same distribution, use balanced XLR, and isolate the laptop with a DI box or line isolator. Never lift the earth: it protects you from electrocution.

How can I tell if a subwoofer is out of phase?

Use a polarity tester, or your ears: play one sub alone, then both side by side. If the bass doesn’t clearly increase, or gets thinner, one of them is reversed.

Build your rig, play your sound

Pick your spot on the real map, buy your gear, load the truck and get ready for the biggest free party. Free, in your browser, nothing to install.

Play for free